801901

Hayward Led Spotlight Handleiding

3
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
Description 3464PLDBL 3469PLDBL 3464LDRGB 3469LDRGB
Consumption in W 18 W
Power supply 12 VAC / 20 VDC 12 VAC
No. of LEDs 252
Lumens 1600 800
White / RGB Cool white RGB
LED Technology CrystaLogic®ColorLogic® (16 programmes, synchronisation, memorisation)
Application Liner – Concrete – Panel Liner – Concrete – Panel Liner – Concrete – Panel Liner – Concrete – Panel
Energy Efciency
This pool light contains
an 81486 removable
LED bulb with a E energy
rating.
The EU2019/2015 and EU2019/2020 regulations do not apply to
this RGB light.
EN
WARNING: Electrical risk.
Non-compliance with these instructions may lead to
serious injury or death.
THE DEVICE IS DESIGNED FOR USE IN POOLS ONLY.
WARNING – Carefully read the instructions in this manual and those on the device. Non-compliance with
the instructions may result in injury.
WARNING – This document must be given to all pool users, who should keep it in a safe place.
WARNING – Always turn off power to the device before handling the electrical installation.
WARNING – This device is not intended for use by those with reduced physical, sensory or intellectual
capacities (in particular children) or by those who do not have the suitable experience or knowledge, unless they
are supervised or have received instructions in how to use the device by the person responsible for their safety.
WARNING – Device installation must be performed in accordance with international standard: IEC 60364-
7-702: LOW-VOLTAGE ELECTRICAL INSTALLATIONS. REQUIREMENTS FOR SPECIAL INSTALLATIONS OR
LOCATIONS. SWIMMING POOLS AND FOUNTAINS.
WARNING – Any electrical installation must be carried out according to standard practice and in compliance
with the applicable regulations.
FNF C 15-100 GB BS7671:1992
DDIN VDE 0100-702 EW EVHS-HD 384-7-702
AÖVE 8001-4-702 HMSZ 2364-702:1994 / MSZ 10-533 1/1990
EUNE 20460-7-702 1993, REBT ITC-BT-31 2002 MMSA HD 384-7-702.S2
IRL IS HD 384-7-702 PL PN-IEC 60364-7-702:1999
ICEI 64-8/7 CZ CSN 33 2000 7-702
LUX 384-7.702 S2 SK STN 33 2000-7-702
NL NEN 1010-7-702 SLO SIST HD 384-7-702.S2
P RSIUEE TR TS IEC 60364-7-702
WARNING – Ensure that children cannot play with the device. When handling it, keep your fingers away from
the openings and moving parts, and make sure no foreign objects enter the device.
WARNING – Only use genuine Hayward spare parts.
WARNING – If the power cable is damaged, to eliminate danger it must be replaced by the manufacturer, their
maintenance agent or by a person with an equivalent qualification (see paragraph below: maintenance).
WARNING – Only operate the spotlight when it is submerged underwater.
WARNING – Only use with a double insulated, safety transformer or power supply.
WARNING – It may be necessary to ask the opinion of a qualified person regarding the installation.
WARNING – The junction box is not supplied.
INSTALLATION GUIDE: FLAT LED POOL SPOTLIGHT
EN
Only use spare parts supplied by Hayward® brands
Description of spotlight
• The LED bulbs (white and coloured) are designed to light up pools of all types (in-ground and
above-ground).
• These spotlights can be installed on all new construction or renovation projects (concrete, liner,
fibreglass or panel).
•
The bulbs are class III and IP68 rated at 1m. They have a very low safety supply voltage of 12VAC
(white and RGB) or 20 VDC (white).
Recommendation for spotlight installation:
The spotlight must point away from the house or patio to prevent intrusive light levels.
The spotlight must be positioned no more than 60 cm below the coping (distance measured from the
bulb axis). The cable attached to the bulb is 2 m long.
The junction box is not supplied. The installation requires a professional opinion.
The installer should select the correct mount for the type of pool.
Make sure the vertical surface on which the spotlight will be mounted is flat.
Concrete pool:
• Drill a hole through
which the bulb cable will
pass, and make the hole
watertight.
• Attach the wall mount
vertically using the
4screws.
• Coil up the extra cable inside the trim ring and screw the trim
ring to the wall mount.
Liner pool:
• Drill a hole
in the wall and
embed the 2“
wall insert.
• Pierce the
liner. Position
the 2 black seals
one of each side of the liner, and attach the mount to the wall
insert using the 4 screws.
• Pass the bulb cable through the cable seal.
• Tighten the seal-tightening nut using a key.
• Coil up the extra cable inside the trim ring and screw the trim
ring to the wall mount.
Panel pool:
• Unscrew the 2 nuts.
• Drill 2 holes in the
panel.
• Position the wall mount
vertically.
• Screw up the upper nut
after putting the seal in
place.
• Put the seal of the lower nut in place, pass the bulb cable
through the seal and screw up the nut.
• Tighten the nut using a key.
• Coil up the extra cable inside the trim ring and screw the trim
ring to the wall mount.
MOUNTING THE SPOTLIGHT ON THE WALL (Series 3464):
MOUNTING THE SPOTLIGHT ON THE WALL (Series 3469):
• Screw the 1.5’’
threaded fitting (b)
onto the spotlight
mount (a) •Screw
the assembly onto
the return fitting (not
supplied), ensuring
the screw hole is at the top. • Pass the spotlight
cable through the return fitting. • Screw the
spotlight onto the spotlight mount (a).
• Place the seal (e)
onto the 1.5’’ threaded
fitting (b) • Screw the
1.5’’ threaded fitting
(b) onto the spotlight
mount (a) • Pass
the spotlight cable
through the hole of the 1.5’’ threaded fitting. •
Screw the spotlight (h) onto the spotlight mount
(a). • Put the seal and seal-tightening nut in place
(d) and tighten it using a key. • Pass the cable
through the return fitting and screw the assembly
onto the return fitting.
• Screw the 2’’
threaded fitting (c)
onto the spotlight
mount (a) •Screw
the assembly onto
the wall feed-through
(not supplied),
ensuring the screw hole is at the top. • Pass the
spotlight cable through the wall feed-through. •
Screw the spotlight (h) onto the spotlight mount
(a).
• Place the opaque
seal (f1) onto the
2’’ threaded fitting
(b) • Screw the 2’’
threaded fitting (b)
onto the spotlight
mount (a) • Pass
the spotlight cable through the hole for the
2’’ threaded fitting. • Position and screw the
spotlight (h) onto the spotlight mount (a). • Put
the seal and seal-tightening nut in place (d) and
tighten it using a key. • Insert the spotlight (h)
into the hole in the panel. • Place the transparent
seal (f2) behind the panel and screw up the
lock-nut (g).
INSTALLATION WITH 1.5” THREADED FITTING INSTALLATION WITH 2” THREADED FITTING
Panel & Liner pool
Waterproofing: the water rises up to
the pool water level Waterproofing at
the return fitting Waterproofing: the water rises up to
the pool water level Waterproofing at the
wall feed-through
Not supplied Not supplied Not supplied
Panel & Liner poolConcrete Pool Concrete Pool
All RGB LEDs (Par 56, Flat, Mini) have the same sequence with 16 programmes
Set colours Colour programmes
#1 White #12 Rainbow, slow transition (130 s)
#2 Blue #13 Rainbow, rapid transition (45 s)
#3 Sky blue #14 Rainbow, no transition (30 s)
#4 Cyan #15 Rainbow (35 s)
#5 Lagoon blue #16 Scrolling from 1 to 15, demo mode
#6 Green
#7 Aqua green
#8 Yellow
#9 Orange
#10 Red
#11 Purple
CONNECTING THE BULB TO THE POWER SUPPLY:
Cable of sufficient length must be left during the renovation to allow the bulb to be replaced out of the water at a
later date if necessary.
• Pass the spotlight bulb cable through the conduit to the junction box.
• Connect the lamp(s) to a transformer which has a secondary circuit output voltage of 12 VAC. The transformer
power (minimum power = 21.5 VA for a white bulb and 21.5 VA for a RGB bulb) must be sufficient for the power of
the lamp(s) that will be connected. In all cases, the sum of the spotlight powers must remain less than or equal to
the transformer power.
• If the connection between the bulb and the transformer is underwater, the connection must be watertight (either
with a double cable-gland, or with epoxy gel). If it is not watertight, water will enter the bulb via the cable.
• Ensure the bulb is fully submerged before use.
• Each spotlight must have a separate protection. 5A and 6A fuses and circuit breakers must be used to provide
protection on the secondary circuit of the transformer.
Example of connection
OPERATION WITH HAYWARD COLOUR LED BULBS:
• All Hayward LED bulbs (PAR56, flat, mini) can be connected and twinned on a single control box.
• Synchronisation:
to turn on all LEDs connected to the same control box under programme 1 (white), use the button
on the box to cut power to the LEDs and switch it on again between 6 and 15 s later.
• Change of programme: use the button on the control box to cut power to the LEDs and switch it on again
between 1 and 3s later.
• Memory: all the LEDs will turn on with the programme most recently saved if power to the LEDs is switched off
for more than 30s.
MAINTENANCE AND END-OF-LIFE DISPOSAL OF BULBS AND REMOTE CONTROL:
• Genuine Hayward spare parts must be used for part replacements. • The bulb must be replaced out of the water. • Replacement of the bulb in this light must only be performed by the manufacturer, their
maintenance agent or by a person with an equivalent qualification. • When the bulb and/or cable is changed, it is recommended that all parts making the device watertight are changed at the same time. •
When the bulb is replaced, the seal and waterproofing elements must also be replaced, ensuring they are positioned correctly. • If the device stops working, the entire LED bulb must be replaced. Do not open
or attempt to repair the bulb. • If the supply cable or its conduit is damaged, to avoid an accident they must be replaced by the manufacturer, an Accredited Service Centre or a qualified technician. • The cable
must comply with the following mechanical and electrical requirements: H05RN-F with a minimum cross-section of 2x1.5mm².
The crossed-out bin symbol indicates selective collection of electrical or electronic devices. This means that these devices and their waste must be taken to waste sorting centres and not thrown
away with household waste. For more information, contact your town hall or the distributor that you bought the product from. Disposal of electrical and electronic devices in the correct manner helps
to avoid potential damage to the environment and human health, and to conserve natural resources.
Electrical
cabinet
for the pool
Main supply
to cabinet Secondary
circuit of lighting
transformer
Optional control box
Minimum power: 18x2 = 36 W
Water
level
Coping
Max 60
cm
P =18W P =18W
230V 12V 12V
PACK CONTENTS (Series 3469)
1 flat LED spotlight
attached cable (2m)
Trim ring + bulb
assembled using screws 1 screw for mounting the
trim ring to the mount
1 spotlight mount 2 seals for 2”
fitting
opaque seal
transparent seal
h a
1 x 1.5” threaded
fitting
b
1 seal for 1.5”
fitting
e
1 seal + seal-
tightening nut
d
1 threaded
fitting 2”
c
Lock-nut for 2”
fitting
g
f1
f2
1 flat LED spotlight
attached cable (2m)
Trim ring + bulb
assembled using screws
1 wall mount
for liner pool
4 screws for mounting on wall 1 screw for mounting the trim ring to the wall mount
1 wall mount for
panel pool
1 wall mount
for concrete pool
PACK CONTENTS (Series 3464)
A
G
E
4 5
3 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hayward Led Spotlight bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hayward Led Spotlight in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Noors als bijlage per email.

De handleiding is 3.16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info