643370
18
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
18 ENGLISH
STANDBY
The STBY function is used if immediate stove switch-o is required when the set temperature has been
reached.
The STBY function can be set at ON or OFF using the procedure described further on.
In the factory the STBY function is always set at OFF (indicator o)
STBY FUNCTION SET AT ON
If the STBY function is active (ON), when the stove reaches the set room temperature and exceeds it by 2°C, it will switch o after a default
delay time, displaying STAND  BY.
When the room temperature is 2°C lower than the setting, the stove will start to work again at the power set on the display, displaying
WORK.
STBY FUNCTION SET AT OFF DEFAULT SETTING
If the stby function is not active (OFF), if the stove reaches the set room temperature, it will go to minimum, modulating and displaying
MODULATION. When the room temperature is below the setting, it will start to work again at the set power, displaying WORK.
CONTROLS PROCEDURE
press key 5 for a few seconds, until SET CLOCK appears.
Press key 3 until "USER" appears.
Press key 5 twice.
Use key 2 or 3 "ON" to activate or "OFF" to de-activaate.
Press key 1 several times to conrm and exit the menu.
N.B.: If these calibrations do not solve the problem, please contact your local customer service centre.
CONTROL PROCEDURE
Press the key 5 for a few seconds; the message SET CLOCK will appear on display.
Press the key 3 for several times to open the EASY SETUP page.
Press the key 5 to conrm.
Use the keys 2 and 3 to increase (3) or decrease (2) the value.
Press the key 1 for several times to conrm and exit the menu.
EASY SETUP
The volumetric weight of the pellet is the ratio between the weight and the volume of the pellet. This ratio can change while maintaining
the quality of the pellet. By using the EASY SETUP function, it is possible to change the calibration of the volumetric weight, increasing or
decreasing the pre-set values.
In the stove program, the values available go from “– 3”to “+ 3”; all the stoves are calibrated at the factory to the optimal value 0
If you notice an excessive deposit on the burner pot, enter the EASY SETUP program and lower the value by one unit to “- 1”; then wait for the
following day and if there is no improvement, lower the value again up to a maximum of “- 3”. Instead, should it be necessary to increase the
calibration of the volumetric weight of the pellet, it is advisable to go from the default value “0” to “+ 1, + 2, + 3” as required.
EXCESSIVE DEPOSIT OF PELLETS IN THE BURNING
POT
NORMAL OPERATION LITTLE DEPOSIT OF PELLETS IN THE BURNING POT
-3 -2 -1 0 +1 +2 +3
THIRD
DECREASING
RANGE IF THE
FIRST TWO ARE
NOT ENOUGH
SECOND
DECREASING
RANGE IF THE
FIRST IS NOT
ENOUGH
FIRST
DECREASING
RANGE (TEST FOR
1 DAY )
OPTIMAL DEFAULT
VALUE
FIRST
INCREASING
RANGE
SECOND
INCREASING
RANGE IF THE
FIRST IS NOT
ENOUGH
THIRD
INCREASING
RANGE IF THE
FIRST TWO ARE
NOT ENOUGH
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Extraflame Giusy bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Extraflame Giusy in de taal/talen: Engels als bijlage per email.

De handleiding is 6,02 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Extraflame Giusy

Extraflame Giusy Gebruiksaanwijzing - Nederlands - 28 pagina's

Extraflame Giusy Gebruiksaanwijzing - Deutsch - 28 pagina's

Extraflame Giusy Gebruiksaanwijzing - Français - 32 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info