Handleiding Enduro EM203 (pagina 36 van 52) (Nederlands, Duits, Engels, Frans)

807572

Verklein

Vergroot

Pagina terug

1/52

Pagina verder

ENDURO® EM203 30 Ref: EM203-UM-TKI-0116-Rev.A.

Changing batteries in the remote control:

When the battery is empty (blue 9V battery LED (Fig. 5J) is blinking), it needs to be replaced.

 Open the rear cover of the handset (Fig. 7A).

 Take out the dead/old battery and dispose in the appropriate way.

 Install a new replacement battery (Fig. 7.1). Make sure to use a leak proof PP3 (9Volt) battery (No claims

under guarantee can be considered for damage caused by leaking batteries).

 Close the rear cover again.

Dead and used batteries may leak and damage the remote control handset! Remove the batteries if the

handset is not going to be used for an extended period.

OPERATION - ELECTRONIC CONTROL UNIT

The electronic control unit (32), which is mounted inside your caravan, is responsible for controlling the

manoeuvring system.

The control unit has three LED’s and one pushbutton (Fig. 3):

Green LED (Fig. 3B): Power LED continuously illuminated when system is activated (by moving slide switch to

“On”-I). If the handset far away from the control unit, beyond the availably distance, this LED will go out.

Blue LED (Fig. 3C): Error message LED concerning caravan battery:

 Blue LED is blinking (2 times blinking, break, 2 times blinking, break etc.): Battery voltage too low (<10V).

Battery needs to be recharged.

 Blue LED is blinking (4 times blinking, break, 4 times blinking, break etc.): Battery Voltage too high (over

charged). Try to discharge the battery by turning on a user (for example a lamp or water-pump).

Red LED (Fig. 3D) is blinking (6 times blinking, break, 6 times blinking, break etc.): Amp overload protection is

activated. Wait about 60 seconds and try again.

In general all error messages will reset automatically after one minute. If this is not the case, reset the

electronics of the manoeuvring system by switching off the system via the isolation switch and the remote

control handset for at least 15 seconds and then turning it on again.

The Reset Button (Fig. 3A): The remote control handset and the control unit are synchronised with each other

in the factory. If the control unit or the remote control handset is replaced, they must be re-synchronised as

described below:

 Check the installation in accordance with the installation instructions and ensure that the drive rollers are

not applied. Check that the battery is properly connected, check the condition of the battery and that a

voltage of 12 V is present at the control unit.

 Please ensure that the battery isolation switch is on.

 Activate the remote control handset by sliding the slide switch to “On”-I (Fig. 5A). The green LED on the

remote control handset (Fig. 5H) starts to flash slowly.

 Press the reset button (Fig. 3A) on the control unit. All three LED’s on the control unit (Fig. 3B, 3C & 3D)

will flash slowly.

 Press both forwards (Fig. 5B) and reverse (Fig. 5C) button on the remote control handset for about 3

seconds. Then the handset buzzer will give a short beep to confirm that the synchronisation is complete.

 After successful synchronisation, the green LED on the control unit (Fig. 3B) and on the remote control

handset (Fig. 5H) will illuminate continuously.

OPERATION - GETTING STARTED

Please make sure you read the safety instructions very carefully and make sure that you

follow these guidelines!

Make sure that the battery that supplies the system is fully charged and in good condition.

Make sure that the caravan is free from the vehicle and the handbrake is on. Also make sure

that the corner steady feet are fully raised.

Fit the end socket of the engagement tool (6) onto the engagement spindle (Fig. 9) on the right or left hand

motor unit. This only needs to be done on one side of your caravan since the other side will automatically follow

via the cross actuation bar.

Turn the handle until it will turn no more without excessive force. The colour of the traction indicator label (Fig.

11A) should be into the green area.

Turn on the battery power isolation switch (29).

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Enduro EM203 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info