702443

Dyson Cinetic Big Ball Handleiding

7
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
7
USING YOUR DYSON APPLIANCE
PLEASE READ THE ‘IMPORTANT SAFETY INSTRUCTIONS’ IN THIS DYSON
OPERATING MANUAL BEFORE PROCEEDING.
RATING PLATE
• Your serial number can be found on your rating plate which is behind the
clear bin.
• Check to ensure your electricity supply corresponds to that shown on the rating
plate. The appliance must only be used as rated.
ASSEMBLY
• Lie the appliance on its back.
• Attach the cleaner head by sliding it on to the connections on the lower front
part of the ball. Ensure the electrical plug on the cleaner head fits into the twin
- block connection on the body of the appliance, which is directly above the
airway. Push firmly: the cleaner head will click into place.
• Stand the appliance up straight.
• Attach the wand handle by sliding it on to the top of the appliance. The spring
clip in the handle will click into place.
• Ensure the hose is straight. Press the red button on the hose. Slide the wand into
the hose.
• Ensure the wand and hose sit in the recess of the handle. Slide the end of the
wand down into the handle to secure it.
• Close the wand cap.
• Slide the tool holder onto the side of the duct as shown.
• Ensure the cyclone and clear bin unit is secured to the main body of
the appliance.
• Attach the tools as shown. In use, the tools can be attached to either the hose or
the wand.
• Wind the cable around the cable hooks. Secure with the clip.
• To watch a short online video visit:
– www.dyson.co.uk/DC75gettingstarted
OPERATION
• Unwind the cable.
• Plug the appliance into the mains electricity supply.
• To switch ‘ON’ or ‘OFF’ press the red power button, located as shown.
• To use, recline the handle. The stabiliser stand will automatically lift up.
• After use, return the appliance to the upright position, pushing it firmly into
place. The stabiliser wheels will automatically lower.
• Then unplug the appliance, coil the cable safely and put the appliance away.
• Switch ‘OFF’ the appliance, unplug and ensure it is upright before:
– changing or using tools
– removing the hose or airway inspection parts.
• Use the cyclone carry handle to carry the machine.
SELF-ADJUSTING CLEANER HEAD WITH
SUCTION CONTROL
• This cleaner head is used for testing with the European Regulations: No.
665/2013 and No. 666/2013.
POWERFUL SUCTION
• For vacuuming of lightly soiled carpets, rugs and hard flooring.
– Your appliance is pre-set to this level of suction when you take it out of
the box.
MAXIMUM SUCTION
• For vacuuming durable floor coverings, hard floors and heavily soiled carpets
and rugs.
– To switch to this setting, move the suction control slider on top of the cleaner
head as shown.
– CAUTION: The suction of this mode can damage delicate flooring. Before
vacuuming, check the flooring manufacturer’s cleaning recommendations.
– If the suction power of Maximum suction prevents easy maneuverability,
switch to Powerful suction mode.
– To switch back to Powerful suction mode, move the suction control slider back
to its original position, as shown.
ATTACHMENTS
• To release the wand, open the wand cap and pull the red tube up and away
from the handle until it clicks into place.
• Should you wish to use the hose without the wand, follow the above instruction
and press the red button to release the wand from the hose.
CARPETS OR HARD FLOORS
• The brush bar will always default to ‘ON’ (spinning) each time you switch the
appliance ‘ON’ and recline it for cleaning.
• The brush bar will not rotate when the appliance is upright.
• To switch the brush bar 'OFF' (e.g. for delicate rugs and delicate flooring):
– switch the appliance ‘ON’
– recline the appliance
– press the brush bar ‘ON/OFF’ button – the brush bar will stop spinning.
• The brush bar will automatically stop if it becomes obstructed. See ‘Brush bar –
clearing obstructions’.
• Before vacuuming your flooring, rugs and carpets, check the manufacturer’s
recommended cleaning instructions.
• Some carpets may fuzz if a rotating brush bar is used when vacuuming. If this
happens, we recommend vacuuming with the brush bar switched 'OFF' and
consulting with the flooring manufacturer.
• The brush bar on the appliance may damage some carpet types. If you are
unsure, turn ‘OFF’ the brush bar.
• Check the brush bar regularly and clear away any debris (such as hair). Debris
left on the brush bar may cause damage to flooring when vacuuming.
LOOKING AFTER YOUR DYSON APPLIANCE
• Do not carry out any maintenance or repair work other than that shown in this
Dyson Operating Manual, or advised by the Dyson Helpline.
• Only use parts recommended by Dyson. If you do not this could invalidate
your guarantee.
• Store the appliance indoors. Do not use or store it below 3°C (37.4°F). Ensure
the appliance is at room temperature before operating.
• Clean the appliance only with a dry cloth. Do not use any lubricants, cleaning
agents, polishes or air fresheners on any part of the appliance.
• If used in a garage, always wipe the base plate and ball with a dry cloth
after vacuuming to clean off any sand, dirt, or pebbles that could damage
delicate floors.
VACUUMING
• Do not use without the clear bin and cyclone in place.
• Fine dirt such as flour should only be vacuumed in very small amounts.
• Do not use the appliance to pick up sharp hard objects, small toys, pins, paper
clips, etc. They may damage the appliance.
• When vacuuming, certain carpets may generate small static charges in the
clear bin or wand. These are harmless and are not associated with the mains
electricity supply. To minimise any effect from this, do not put your hand or
insert any object into the clear bin unless you have first emptied it and rinsed it
out with cold water (see ‘Cleaning the clear bin’).
• Do not work with the appliance above you on the stairs. When cleaning stairs it
is recommended that the handle is not extended and that you use a tool on the
end of the hose rather than the wand.
• Do not put the appliance on chairs, tables, etc.
• Before vacuuming highly polished floors, such as wood or lino, first check that
the underside of the floor tool and its brushes are free from foreign objects that
could cause marking.
• Do not leave the cleaner head in one place on delicate floors.
EMPTYING THE CLEAR BIN
• Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
• Switch ‘OFF’ and unplug before emptying the clear bin.
• To remove the cyclone and clear bin unit, press down on the red button on the
top of the carrying handle on the cyclone.
• To release the dirt, press all the way down on the same red button on the top of
the carrying handle on the cyclone.
• To minimise dust/allergen contact when emptying, encase the clear bin tightly in
a plastic bag and empty.
• Remove the clear bin carefully from the bag.
• Seal the bag tightly, dispose as normal.
• To refit:
– ensure the airway in the bin base is clear of dust and dirt
– close the clear bin base so it clicks into place
– push the cyclone and clear bin unit into the main body of the appliance; it will
click into place
– ensure the cyclone and clear bin unit is secure.
CLEANING THE CLEAR BIN
• Remove the cyclone and clear bin (see ‘Emptying the clear bin’).
• To separate the cyclone unit from the clear bin press the red button to open the
clear bin base. Press the silver button and separate the cyclone unit from the
clear bin.
• Clean the clear bin with cold water only.
• Do not use detergents, polishes or air fresheners to clean the clear bin.
• Do not put the clear bin in a dishwasher.
• Do not immerse the whole cyclone in water or pour water into the cyclones.
• Clean the cyclone shroud with a cloth or the provided brush to remove any lint
and dust.
• Ensure the clear bin is completely dry before replacing.
• To refit:
– fit the cyclone shroud into the clear bin so that the silver button clicks and
engages. Ensure that the front of the clear bin is locked in place
– close the clear bin base so it clicks into place
– push the cyclone and clear bin unit into the main body of the appliance; it will
click into place
– ensure the cyclone and clear bin unit is secure.
BLOCKAGES – THERMAL CUT-OUT
• This appliance is fitted with an automatically resetting thermal cut-out.
• Large items may block the tools or wand inlet. If any part becomes blocked the
appliance may overheat and automatically cut-out.
• If this happens, follow the instructions below in ‘Looking for blockages’.
LOOKING FOR BLOCKAGES
• Switch ‘OFF’ and unplug before looking for blockages. Failure to do so could
result in personal injury.
• Leave to cool down for 1-2 hours before looking for blockages.
• Clear any blockage before restarting.
• Look for blockages in the wand, airways and cleaner head.
• To release the hose from the machine, you will need to remove the wand.
• Open the wand release cap.
• Pull the wand up and away from the handle.
• Press the red release button in the connecting collar and remove the wand from
the hose.
• Remove the clear bin and cyclone unit. Then release the hose from the appliance
by pressing the red tab on the base of the hose –you can see it from the front of
the appliance.
• Check for blockages in the hose.
• Beware of sharp objects when checking for blockages.
• To refit the hose, align the guides on the base of the hose with the channels in
the neck of the airway. Ensure the red tab faces the front of the appliance. Push
the hose on. It will click into place. To refit the wand follow the instructions above
in the ‘Operation’ section.
• To remove the base plate to access an obstruction, see ‘Base plate –
disassembly/reassembly’.
… 7 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dyson Cinetic Big Ball bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dyson Cinetic Big Ball in de taal/talen: Engels als bijlage per email.

De handleiding is 3,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Dyson Cinetic Big Ball

Dyson Cinetic Big Ball Gebruiksaanwijzing - Alle talen - 56 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info