591334
33
Verklein
Vergroot
Pagina terug
1/156
Pagina verder
31
ENGLISH
After interrupting the cut, do not switch on
until the core bit can rotate freely.
Always trigger off the switch to prevent the
machine from accidentally self starting.
Note this procedure especially after the
power supply is interrupted or the plug is
disconnected from the power outlet.
Mounting the tool onto a stand is
recommended to increase the user comfort
and reduce the risk of injuries.
In case of jammed core bit disconnect the
machine from the power supply, remove
the reason for the jam before turning on the
machine again.
DRY DRILLING
Dry drilling is suitable for masonry
(bricks, breeze blocks).
Always use a suitable dust extractor.
Always use core bits designed for dry drilling.
Do not use the machine handheld with core
bits larger than 100 mm.
Always mount the drill on a stand when
drilling holes larger than 100 mm.
Wear a dust mask when performing dry cuts.
D21583 - WET DRILLING
Wet drilling is suitable for stone and concrete.
Always use a water cooling device and a
water collection system.
Always use core bits designed for wet drilling.
The maximum water pressure is 3 bar. Use
a pressure relieve valve in case of a higher
water pressure.
Use only pure tap water for cooling
purposes.
Prevent water from entering the motor or
other electrical components. Make sure the
PRCD is not in contact with water.
Safe Operation for Stationary Stands
A machine incorrectly assembled may
cause a hazardous situation. Carefully fix the
machine into the drill stand and check that
the drill stand holder is secured.
Fixing the drill stand with vacuum device can
lead to dangerous situations.
Check the surface where the drill stand shall
be fixed. surface such as irregular (rough) can
significantly reduce the effectiveness of the
suction system. Coated or laminated surface
can be pulled off during work.
The minimum vacuum level shall not be lower
than 600mbar. Periodically control this value
on the pressure gauge.
Do not use drill core bits with a diameter
greater than 202 mm at this application.
5) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional Specifi c Safety Rules for
Diamond Drills
Wear ear protectors. Exposure to noise can
cause hearing loss.
Hold power tools by insulated gripping
surfaces when performing an operation
where the cutting tool may contact hidden
wiring or its own cord. Cutting accessory
contacting a “live” wire may make exposed
metal parts of the tool “live” and shock the
operator.
Use auxiliary handles supplied with the
tool. Loss of control can cause personal
injury.
Wear safety goggles or other eye
protection. Drilling operations cause chips to
fly. Flying particles can cause permanent eye
damage.
Bits, tools and drilling area get hot during
operation. Wear gloves when touching
them.
Use the diamond drill under constant
supervision.
Make sure not to cut through electric mains,
gas or water pipes. Use detection systems
prior to drilling.
Make sure the cutting accessory is fitted
properly.
Check all screws and tighten securely before
you use the machine.
When drilling downward, make sure the core
can drop safely without injuring someone
standing beneath.
Do not perform overhead (upward) drilling
without the use of suitable protection
shielding (water collecting device).
When drilling handheld, always use the side
handle and hold the machine firmly with both
hands.
Make sure to stand on a stable surface and
keep body balance at all times for better
control of reaction torque.
Inspect the machine before every use. Do not
use the machine if there are any defectives
on the mains plug, power cord, trigger switch
or any part of the housing. Have the machine
repaired by an authorized repair agent.
Do not use the machine in a damp or wet
location.
Switch off the machine immediately if there is
any leak of water.
33

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt D21583K T-2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt D21583K T-2 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 8,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info