If your apparatus has only 1 control knob
Read steps 1 to 5 before beginning with step 1.
1) Make sure the control knob is in the "off" (l) position.
2) Push the end of the hose completely onto the regulator
nozzle and secure with a suitable clip.Fit the regulator onto
the gas cylinder in accordance with its instructions.
3) Open the gas cylinder valve.
4) Press the control knob and turn it to the full flame ()
position, then immediately press the igniter button ( )
until you hear the click. Repeat 3 or 4 times if
necessary until the burner is lit.
5) If the burner fails to light, turn the control knob to the "off"
position (l). Wait 5 minutes before repeating the operation.
Important:
If the burner fails to light after the 2
nd
attempt, turn the
control knob to the "off" position (l) and check that the
burner outlets and the venturi tube are not blocked.
i) Grill burner-manual lighting
If the automatic ignition should fail to operate, turn the control
knob to the "off" position (l) and wait 5 minutes. Insert a
burning match into one of the side openings of the base, and
turn the knob on the right of the control panel onto the full
flame ( ) position.
j) Turning off the grill burner
Return the control knobs to the "off" position (l), then close
the cylinder valve.
k) Lighting the side stove (if applicable to your model)
The stove may operate independently or in conjunction with
the grill burner.
Lighting:
- open the gas cylinder valve.
- check that there is no gas leak between the gas cylinder and
the stove.
- check the condition of the hose connecting the grill burner
to the stove. Should it present cracks, call our After Sales
Service to have it replaced.
- open the valve of the stove (towards the +) and press the
igniter button ( ) until you hear the click. Repeat three or
four times if necessary. Should the stove fail to light, present
a match to the edge of the burner.
- adjust the size of the flame to the dimensions of the
container you are using by opening the valve to various
extents. Do not use a container smaller than 10 cm or larger
than 26 cm.
l) Turning off the side stove (if applicable to your model)
Close the stove valve (towards the -) and the valve of the gas
cylinder if the grill burner is not in use.
m) Replacing the gas cylinder
- Always work in a well ventilated area and never in the
presence of a flame, spark or heat source.
- Return the control knobs in the "off" position (l) then close
the cylinder valve.
- Remove the regulator, check that the sealing joint is in good
condition.
- Put the full cylinder in place, refit the regulator,taking care not
to apply stress to the hose. Check for gas leaks.
n) Operation
If your apparatus has a lid
- It's recommended that protective gloves be worn to handle
components which may be very hot.
- Before cooking, preheat the barbecue for about 10 minutes
in the full flame ( ) position with the lid closed.
When using the barbecue for the first time, preheat for
about 20 minutes in the full flame ( ) position, in order to
eliminate the smell of paint from new components.
Cooking rate can be adjusted, depending upon the position of
the control knobs.
e) Lid (depending on model)
Handle the lid carefully, especially during operation.Do not lean
over the base
f) Checking for gas leaks
1) Work outside, away from all sources of ignition. Do not
smoke.
2) Make sure the control knobs are in the "off" (l) position.
3) Push the end of the hose completely onto the regulator
nozzle and secure with a suitable clip.
4) Fit the regulator onto the gas cylinder in accordance with
its instructions.
5) Use a gas leak solution to test for leaks. Important: never
use a naked flame to check for gas leaks.
6) Apply the solution to the connections cylinder/regulator/
hose/apparatus (the control knobs should remain closed: off
position). Open the gas cylinder valve.
7) Bubbles in the gas leak solution indicate that there are gas
leaks.
8) The leak can be stopped by tightening any hose connection
or replacing any faulty component. The barbecue must not
be used until the leak is stopped.
9) Close the valve on the gas cylinder. Check for leaks at least
once per year and each time the gas cylinder is replaced.
g) Prior to use
Never use the barbecue until the instructions have been read
carefully and understood. Also, make certain that:
- there are no leaks
- the venturi tubes are not blocked
- the hose does not touch any components which may get hot.
- that the ventilation openings in the gas receptacle housing are
not obstructed, if appropriate.
Check that the venturi tubes (VT) cover
the injectors (IJ).
h) Lighting the grill burner
If your apparatus has 2 control knobs
Read steps 1 to 7 before beginning with step 1.
1) Never light the barbecue with the lid closed, only
with the lid open.
2) Make sure the 2 control knobs are in the "off" (l) position.
3) Push the end of the hose completely onto the regulator
nozzle and secure with a suitable clip.Fit the regulator onto
the gas cylinder in accordance with its instructions.
4) Open the gas cylinder valve.
5) Press one of the 2 control knobs and turn it to the full
flame ( ) position, then immediately press the igniter
button ( ) until you hear the click. Repeat 3 or
4 times if necessary until the burner is lit.
6) If the burner fails to light, turn the control knob to the "off"
position (l). Wait 5 minutes before repeating the
operation.
7) As soon as the burner is lit, the other burner automatically
lights when the second control knob is placed in the full
flame ( ) position without pushing the automatic igniter
button again.
Important:
If the burner fails to light after the 2
nd
attempt, turn the
control knob to the "off" position (l) and check that the
burner oulets and venturi tubes are not blocked.
8
