110140
26
Verklein
Vergroot
Pagina terug
1/151
Pagina verder
26 | English
1 609 929 N78 | (7.2.08) Bosch Power Tools
The guide-rail adapter 26 is required for working
with the guide rail 27. The guide-rail adapter 26
is mounted in the same manner as the parallel
guide 10.
The following work steps are required for exact
cuts using the guide rail 27:
Place the guide rail 27 on to the workpiece
projecting lightly over the side. Pay attention
that the side with the rubber lip faces to the
workpiece.
Set the circular saw with the premounted
guide-rail adapter 26 on to the guide rail 27.
Adjust the desired cutting depth and the bev-
el angle. Observe the marks on the guide-rail
adapter 26 for preadjustment of the various
bevel angles; see figure F.
Align the circular saw with guide-rail adapter
in such a manner that the teeth of the saw
blade 21 face against the rubber lip. The po-
sition of the saw blade 21 depends on the se-
lected cutting angle. Do not saw into the
guide rail.
Tighten wing bolt 7 to lock the position of the
guide-rail adapter.
Remove the circular saw with the premount-
ed guide-rail adapter 26 from the guide rail
27.
Align the guide rail 27 on the workpiece in
such a manner that the rubber lip lies exactly
alongside the cutting edge.
Fasten the guide rail 27 with suitable clamp-
ing devices, e. g., screw clamps, on the work-
piece. Set the circular saw with the pre-
mounted guide-rail adapter 26 on to the
guide rail.
Switch the machine on and guide it in the
cutting direction applying moderate and
steady feed.
Two guide rails can be connected to one with
use of the connection piece 28. Clamping is car-
ried out with the four screws located in the con-
nection piece.
Maintenance and Service
Maintenance and Cleaning
f Before any work on the machine itself, pull
the mains plug.
f For safe and proper working, always keep
the machine and ventilation slots clean.
The retracting blade guard must always be able
to move freely and retract automatically. There-
fore, always keep the area around the retracting
blade guard clean. Remove dust and chips by
blowing out with compressed air or with a
brush.
Saw blades that are not coated can be protect-
ed against corrosion with a thin coat of acid-free
oil. Before use, the oil must be removed again,
otherwise the wood will become soiled.
Resin and glue residue on the saw blade produc-
es poor cuts. Therefore, clean the saw blade im-
mediately after use.
If the machine should fail despite the care taken
in manufacturing and testing procedures, repair
should be carried out by an after-sales service
centre for Bosch power tools.
In all correspondence and spare parts order,
please always include the 10-digit article
number given on the type plate of the machine.
0° 1
-
45°
OBJ_BUCH-179-003.book Page 26 Thursday, February 7, 2008 9:51 AM
26

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Bosch-PKS-40

Zoeken resetten

  • Enige tijd geleden een Bosch PKS 40 cirkelzaag gekocht, maar de gebruiksaanwijzing ontbreekt.
    Kunnen jullie een gebruiksaanwijzing toesturen?
    Gesteld op 28-12-2020 om 16:26

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch PKS 40 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch PKS 40 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 4,86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Bosch PKS 40

Bosch PKS 40 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanôl, Polski, Dansk, Svenska, Norsk, Suomi - 88 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info