786202
31
Verklein
Vergroot
Pagina terug
1/499
Pagina verder
English | 31
Protective guard for grinding
Place the protective guard
(15) onto the holder on the
power tool until the coding
cams of the protective guard
are aligned with the holder.
When doing so, press and
hold the unlocking lever (1).
Press the protective guard
(15) onto the spindle collar
until the shoulder of the pro-
tective guard is sitting on the
flange of the power tool and
rotate the protective guard
until it audibly clicks into
place.
Adjust the position of the protective guard (15) to meet the
requirements of the operation. To do this, push the unlock-
ing lever (1) upward and rotate the protective guard (15)
into the required position.
uAlways position the protective guard(15) such that
the two cams on the unlocking lever(1) engage in the
corresponding openings on the protective guard(15).
uAdjust the protective guard (15) such that sparking in
the direction of the operator is prevented.
uThe protective guard (15) must only be adjustable
while the unlocking lever (1) is actuated. Otherwise,
the power tool must not be used any more under any
circumstances and must be sent to the after-sales ser-
vice.
Note: The coding cams on the protective guard (15) ensure
that only a protective guard that is suitable for the power
tool can be fitted.
Protective guard for cutting
uFor cutting, always use the protective guard for
cutting(17) or the protective guard for grinding (15)
together with the cover for cutting(18).
uProvide sufficient dust extraction when cutting stone.
The protective guard for cutting(17) is fitted in the same
way as the protective guard for grinding(15).
Metal cover for cutting
Fit the metal cover for cutting(18) on the protective guard
for grinding(15) (see figureA): Swivel the tool retainer back
(). Attach the cover(18) to the protective guard for
grinding(15) (). Press the tool retainer firmly into place
on the protective guard(15) ().
To remove the cover (see figureB), press the button on the
tool retainer () and swivel it back (). Remove the
cover(18) from the protective guard(15) ().
Plastic cover for cutting
Attach the plastic cover for cutting(18) to the protective
guard for grinding(15) (see figureC). The cover(18) aud-
ibly and visually engages on the protective guard(15).
To remove the cover (see figureD), unlock the cover(18) on
the left- or right-hand side of the protective guard(15) ()
and remove the cover ().
Extraction guard for cutting with a guide block
The extraction guard for cutting with a guide block (29) is fit-
ted in the same way as the protective guard for grinding
(15).
Hand guard
uAlways fit the hand guard (22) when working with the
rubber sanding pad (23) or with the cup brush/conical
brush/diamond annular cutter.
Attach the hand guard (22) to the side handle (11).
Standard auxiliary handle/low-vibration auxiliary handle
Screw the auxiliary handle (11)/(12) on the right or left of
the machine head depending on the working method.
uDo not operate your power tool without the auxiliary
handle(11)/(12).
uDo not continue to use the power tool if the auxiliary
handle (11)/(12) is damaged. Do not make any altera-
tions to the auxiliary handle (11)/(12).
The low-vibration auxiliary
handle (12) reduces vibra-
tion, enabling the tool to be
used safely and more com-
fortably.
Fitting and removing abrasive tools
Follow the special assembly instructions for
X-LOCK application tools.
uRemove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
uDo not touch grinding and cutting discs until they have
cooled down. The discs can become very hot while work-
ing.
uOnly use original X-LOCK application tools that carry the
X-LOCK logo. A maintained clamping gauge of max.
1.6mm can only be guaranteed with original X-LOCK ap-
plication tools. A higher clamping gauge can lead to insec-
ure clamping, potentially causing the clamp tool to come
loose.
uX-LOCK application tools do not need additional clamping
flanges or support flanges.
uMake sure that the application tool and the holder are not
deformed and are free from dirt and particles.
Pay attention to the dimensions of the abrasive tools.
Make sure that both X-LOCK catches are open (see figure
below) before fitting the X-LOCK application tool.
If necessary, clean the area between the two X-LOCK
catches.
Fitting the abrasive tool
Place the grinding/cutting/flap disc in a central position
on the X-LOCK holder, parallel to the bearing surface
and with the right side facing up.
Push the disc into the holder.
Bosch Power Tools 1 609 92A 6WT | (24.06.2022)
31

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GWX 18V-15 P bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GWX 18V-15 P in de taal/talen: Alle talen als bijlage per email.

De handleiding is 29.9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info