Handleiding Bosch GWS 24-180 P (pagina 24 van 325) (Alle talen)

786337

Verklein

Vergroot

Pagina terug

1/325

Pagina verder

24 | English

Starting current limitation

(GWS24-180JZ / GWS24-230JZ / GWS24-230PZ)

The electronic starting current limitation feature restricts the

power of the power tool when it is switched on and enables

operation using a 16 A fuse.

Note: If the power tool runs at full speed immediately after

being switched on, this means that the starting current limit-

ation and restarting protection mechanisms have failed. The

power tool must be sent to the after-sales service immedi-

ately; see the "After-Sales Service and Application Service"

section for addresses.

Overload protection

(GWS24-180JZ / GWS24-230JZ / GWS24-230PZ)

When overloaded, the motor comes to a stop. Allow the

power tool to cool down unloaded at its maximum no-load

speed for approx. 5–10 seconds.

Emptying the dust box (see figureA)

(GWS24-180JZ / GWS24-230JZ / GWS24-230PZ)

Press both sides of the dust box(3) and remove the dust

box(3) from the power tool. Open the cover and empty the

dust box(3). Slide the dust box(3) back into the power tool

until it clicks into place.

Working Advice

uPull the plug out of the socket before carrying out any

work on the power tool.

uExercise caution when cutting slots in structural walls;

see the "Information on structural design" section.

uClamp the workpiece if it is not secure under its own

weight.

uDo not load the power tool so heavily that it comes to a

stop.

uIf the power tool has been subjected to a heavy load,

continue to run it at no-load for several minutes to

cool down the accessory.

uDo not use the power tool with a cut-off stand.

uDo not touch grinding and cutting discs until they have

cooled down. The discs can become very hot while work-

ing.

Note: Remove the plug from the socket when not using the

tool. When the power tool is plugged in, mains voltage is

present and the tool consumes a small amount of electricity,

even if switched off.

Rough grinding

uNever use cutting discs for rough grinding.

The best rough grinding results are achieved with a set angle

of 30° to 40°. Move the power tool back and forth with mod-

erate pressure. This will ensure that the workpiece does not

become too hot or discolour and that grooves are not

formed.

Flap Disc

With the flap disc (accessory), curved surfaces and profiles

can be worked. Flap discs have a considerably higher ser-

vice life, lower noise levels and lower sanding temperatures

than conventional sanding sheets.

Cutting Metal

uAlways use the protective guard for cutting (14) when

cutting with bonded abrasives.

When carrying out abrasive cutting, use a moderate feed

that is suited to the material being machined. Do not exert

pressure on the cutting disc and do not tilt or swing the

power tool.

Do not attempt to reduce the speed of a cutting disc coming

to a stop by applying pressure from the side.

The power tool must always

work in an up-grinding mo-

tion. Otherwise, there is a

risk that it will be pushed

uncontrolled out of the cut.

For best results when cut-

ting profiles and rectangular

tubing, start at the smallest

cross section.

Cutting stone

uProvide sufficient dust extraction when cutting stone.

uWear a dust mask.

uThe power tool may be used only for dry cutting/grind-

ing.

For best results when cutting stone, use a diamond cutting

disc.

When using the extraction guard for cutting with a guide

block (22), the vacuum cleaner must be approved for vacu-

uming stone dust. Suitable vacuum cleaners are available

from Bosch.

Switch on the power tool

and position it with the

front part of the guide block

on the workpiece. Move the

power tool with a moderate

feed motion that is suited to

the material being ma-

chined.

When cutting especially

hard materials such as con-

crete with a high pebble content, the diamond cutting disc

can overheat and become damaged as a result. This is

clearly indicated by circular sparking, rotating with the dia-

mond cutting disc.

If this happens, stop cutting and allow the diamond cutting

disc to cool down by running the power tool for a short time

at maximum speed with no load.

Working noticeably slower and with circular sparking indic-

ate that the diamond cutting disc that has become dull. You

can resharpen the disc by briefly cutting into abrasive mater-

ial (e.g. lime-sand brick).

1 609 92A 5TE | (29.07.2021) Bosch Power Tools

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Bosch GWS 24-180 P Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info