Handleiding Bosch GHO 15-82 Professional (pagina 14 van 164) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins)

593157

Verklein

Vergroot

Pagina terug

1/164

Pagina verder

14 | English

1 609 92A 11E | (1.12.14) Bosch Power Tools

Dust/Chip Extraction

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suitable

for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the mate-

rials to be worked.

Clean the chip ejector 3 regularly. Use a suitable tool (e.g., a

piece of wood, compressed air, etc.) to clean a clogged chip

ejector.

 Do not reach into the chip ejector with your hands. They

could be injured by rotating parts.

To ensure optimum extraction of dust/chips, always work

with external dust extraction or a chip/dust bag.

External Dust Extraction (see figure C)

Mount the vacuum hose 14 (accessory) on to the chip ejector

Connect the vacuum hose 14 to a vacuum cleaner (accesso-

ry). An overview for connecting to various vacuum cleaners

can be found at the end of this manual.

The vacuum cleaner must be suitable for the material being

worked.

When vacuuming dry dust that is especially detrimental to

health or carcinogenic, use a special vacuum cleaner.

Integrated Dust Extraction (see figure C)

A chip/dust bag (accessory) 15 can be used for smaller jobs.

Insert the sleeve of the chip/dust bag firmly into the chip ejec-

tor 3. Empty the chip/dust bag 15 at regulary intervals to

maintain optimum dust collection.

Operation

Operating Modes

Adjusting the Planing Depth

With the adjustment knob 2, the planing depth can be adjust-

ed variably from 0–1.5 mm using the planing depth scale 1

(scale graduation = 0.1 mm).

Park Rest (see figure D)

The park rest 16 allows the machine to be set down directly

after operation, without danger of damaging the working sur-

face or the planer blade. While planing, the park rest 16 is tilt-

ed upwards thus enabling full contact of the rear part of the

planer base plate 6.

Note: The park rest 16 may not be removed.

Starting Operation

 Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

Switching On and Off

To save energy, only switch the power tool on when using it.

To start the machine, first push the lock-off button for the

On/Off switch 4 and then press the On/Off switch 5 and keep

it pressed.

To switch off the machine, release the On/Off switch 5.

Note: For safety reasons, the On/Off switch 5 cannot be

locked; it must remain pressed during the entire operation.

Working Advice

 Before any work on the machine itself, pull the mains

plug.

Planing (see figure D)

Set the required planing depth and place the front part of the

planer base plate 6 against the workpiece.

 Apply the machine to the workpiece only when

switched on. Otherwise there is danger of kickback when

the cutting tool jams in the workpiece.

Switch the machine on and guide the machine with even feed

over the surface to be planed.

To achieve high-grade surfaces, work only with low feed and

apply pressure on the centre of the planer base plate.

When machining hard materials (e.g. hardwood) as well as

when utilising the maximum planer width, set only low planing

depths and reduce planer feed, as required.

Excessive feed reduces the surface quality and can lead to

rapid clogging of the chip ejector.

Only sharp blades achieve good cutting capacity and give the

machine longer life.

The integrated park rest 16 also allows for continued planing

at any given location on the workpiece after an interruption:

– With the park rest folded down, place the machine on the

location of the workpiece where the planing is to be contin-

ued.

– Switch on the machine.

– Apply the supporting pressure onto the front part of the

planer base plate and slowly push the machine forward

(). This tilts the park rest upward () so that the rear

part of the planer base plate faces on the workpiece again.

– Guide the machine over the surface to be planed () with

even feed.

Beveling Edges (see figure E)

The V-grooves in the front planer base plate allow quick and

easy beveling of workpiece edges. Depending on required

bevel width, use the corresponding V-groove. For this, place

the planer with the V-groove onto the edge of the workpiece

and guide it along the edge.

OBJ_BUCH-865-006.book Page 14 Monday, December 1, 2014 7:58 AM

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Bosch GHO 15-82 Professional Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info