592623
19
Verklein
Vergroot
Pagina terug
1/227
Pagina verder
English | 19
Bosch Power Tools 1 609 92A 0Y1 | (17.9.14)
Place the workpiece against the angle stop 7.
Slide the clamping spindle 8 against the workpiece and
firmly clamp the workpiece with the spindle handle 10.
Loosening the Workpiece
Loosen the spindle handle 10.
Tilt up the quick release 9 and pull the clamping spindle 8
away from the workpiece.
Starting Operation
Observe the mains voltage! The voltage of the power
source must correspond with the data on the type plate of
the machine.
Check the cutting disc before using. The cutting disc
must be properly mounted and must rotate freely. Car-
ry out a 30 second (min.) test run with no load. Do not
use damaged, out-of-centre or vibrating cutting discs.
Damaged cutting discs can burst and cause injuries.
Dusts from materials such lead-containing coatings, minerals
and metal can be harmful to one’s health. Contact with or in-
haling the dusts can trigger allergic reactions to the operator
or bystanders and/or lead to respiratory infections.
Certain metal dusts are considered hazardous, especially in
conjunction with alloys such as zinc, aluminium or chromium.
Materials containing asbestos may only be worked by special-
ists.
Provide for good ventilation of the working place.
It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the mate-
rials to be worked.
The blade can be blocked by dust, chips or workpiece frag-
ments in the slot of the base plate 12.
Switch the machine off and pull the mains plug from the
socket outlet.
Wait until the cutting disc has come to a complete stop.
Tilt the machine toward the rear, so that small workpiece
fragments can fall out of the opening intended for this pur-
pose.
If required, use a suitable tool to remove all workpiece frag-
ments.
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Position of the Operator (see figure F)
Do not stand in a line with the cutting disc in front of the
machine. Always stand aside of the cutting disc. This
measure provides for better protection of your body
against possible splinters in case of cutting disc breakage.
Switching On and Off (see figure G)
To save energy, only switch the power tool on when using it.
–To start the machine, firstly press the lock-off button 1.
Then press the On/Off switch 2 and keep it pressed.
Note: For safety reasons, the On/Off switch 2 cannot be
locked; it must remain pressed during the entire operation.
–To switch off the machine, release the On/Off switch 2.
Soft starting
The electronic soft starting feature limits the torque upon
switching on and increases the working life of the motor.
Working Advice
General Cutting Instructions
Do not touch the cutting disc after working before it
has cooled. The cutting disc becomes very hot while work-
ing.
Make sure that the spark guard 20 is properly mount-
ed. Sparking occurs when cutting metal.
Protect the cutting disc against impact, shock and grease. Do
not subject the cutting disc to lateral pressure.
Do not strain the power tool so heavily that it comes to a
standstill.
Excessive feed considerably reduces the performance capa-
bility of the machine and shortens the service life of the cut-
ting disc.
Use only cutting discs that are suitable for the material to be
worked.
Permissible Workpiece Dimensions
Maximum workpiece sizes:
Minimum workpiece sizes
(= all workpieces that can be clamped via the clamping spin-
dle 8): Length 80mm
Cutting depth, max. (0°/0°): 125 mm
Cutting Metal
Set the desired mitre angle.
Firmly clamp the workpiece as appropriate for its dimen-
sions.
Switch on the machine.
Slowly guide the tool arm downward with the handle 3.
Cut the workpiece applying uniform feed.
Switch the machine off and wait until the cutting disc
comes to a complete stop.
Guide the tool arm slowly upward.
Mitre/Bevel Angle
Workpiece Form 45°
125 Ø 100 Ø
110 x 110 82 x 82
180 x 85 90 x 75
130 x 130 75 x 75
OBJ_BUCH-1063-004.book Page 19 Wednesday, September 17, 2014 9:34 AM
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GCO 2000 Professional bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GCO 2000 Professional in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 9,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info