Handleiding Bosch GBH 18V-28 DC (pagina 20 van 307) (Alle talen)

786123

Verklein

Vergroot

Pagina terug

1/307

Pagina verder

20 | English

This may significantly reduce vibration and noise emissions

over the total working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping their hands warm,

and organising workflows correctly.

Dust emission information: with Bosch GDE 28 D

Professional

Dust emission values determined according

toEN50632-2-6:

Respirable dust:<0.50mg/m3, K=0mg/m3

Inhalable dust:0.80mg/m3, K=0.2mg/m3

Quarz dust:<0.05mg/m3

The indicated dust emission value was determined under the

following operating conditions:

Operating mode: Hammer drilling

Application tool: SDS–plus drill bit, diameter16 mm

Note: If the power tool is used in another operating mode,

with other application tools or is poorly maintained, the dust

emission value may differ. This may significantly increase

dust emissions over the total working period.

If necessary, establish additional safety measures to protect

the operator from the effects of dust emissions, for example:

Wear a P2 filter class breathing mask.

The regulations on the material being machined that apply in

the country of use must be observed.

Assembly

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Battery Charging

uUse only the chargers listed in the technical data. Only

these chargers are matched to the lithium-ion battery of

your power tool.

Note: The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger

before using your power tool for the first time.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

uDo not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

Follow the instructions on correct disposal.

Removing the battery

The battery(8) is equipped with two locking levels to pre-

vent the battery from falling out if the battery release

button(16) is pressed unintentionally. As long as the bat-

tery is inserted in the power tool, it is held in position by

means of a spring.

– To remove the battery(8), press the release button(16)

and pull the battery out of the power tool. Do not use

force to do this.

Battery charge indicator

The green LEDs on the battery charge indicator indicate the

state of charge of the battery. For safety reasons, it is only

possible to check the state of charge when the power tool is

not in operation.

Press the button for the battery charge indicator or to

show the state of charge. This is also possible when the bat-

tery is removed.

If no LED lights up after pressing the button for the battery

charge indicator, then the battery is defective and must be

replaced.

Battery model GBA 18V...

LEDs Capacity

3× continuous green light 60−100%

2× continuous green light 30−60%

1× continuous green light 5−30%

1× flashing green light 0−5%

Battery model ProCORE18V...

LEDs Capacity

5× continuous green light 80−100%

4× continuous green light 60−80%

3× continuous green light 40−60%

2× continuous green light 20−40%

1× continuous green light 5−20%

1× flashing green light 0−5%

Auxiliary handle

uDo not operate your power tool without the auxiliary

handle(15).

Swivelling the auxiliary handle (see figure A)

You can swivel the auxiliary handle (15) to any angle for a

safe work posture that minimises fatigue.

– Turn the lower gripping end of the auxiliary handle (15)

anticlockwise and swivel the auxiliary handle (15) into

the required position. Then turn the lower gripping end of

1 609 92A 80W | (05.07.2022) Bosch Power Tools

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Bosch GBH 18V-28 DC Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info