709449
16
Verklein
Vergroot
Pagina terug
1/148
Pagina verder
16
ENGLISH
(Original instructions)
Alternative method for cutting crown molding
Place the molding at an angle between the fence (12) and the
saw table (11), with the top side of the molding on the table
and the bottom side of the molding on the fence as shown
in gure S2.
The advantage to cutting crown molding using this method
is that no bevel cut is required. Minute changes in the miter
angle can be made without affecting the bevel angle. This
way,when corners other than 90º are encountered, the saw
can be quickly and easily adjustedfor them.
Instructions for cutting crown molding angled
between the fence and base of the saw for all cuts
This saw can cut up to 14 mm x 92 mm crown molding nested.
u Angle the molding so the bottom of the molding (part
which goes against the wall when installed) is against the
fence (12) and the top of the molding is resting on the saw
table (11), as shown in gure S2.
u The angled “ats” on the back of the molding must rest
squarely on the fence and saw table.
Inside Corner Outside Corner
Left Side Miter right at 45°
Save right side of cut
Miter left at 45°
Save right side of cut
Right Side Miter left at 45°
Save left side of cut
Miter right at 45°
Save left side of cut
Special Cuts
Never make any cut unless the material is secured on the
table and against the fence.
Bowedmaterial(g.T1,T2)
When cutting bowed material always position it as shown in
gure T1 and never like that shown in gure T2. Positioning
the material incorrectly will cause it to pinch the blade near
the completion of the cut.
Cutting round material
Rounded material should be clamped or held rmly to the
fence to keep It from rolling. This is extremely important when
making angle cuts.
Cuttinglargematerial(g.U)
Occasionally you will encounter a piece of wood a little too
large to t beneath the lower guard.
To clear the guard over the wood, with the saw off and your
right hand on the operating handle, place your right thumb
outside of the upper portion of the guard and roll the guard up
just enough to clear the wood, as shown in gure U. Release
the guard prior to starting the motor. The guard mechanism
will function properly during the cut. Only do this when neces-
sary.
NEVER TIE, TAPE, OR OTHERWISE HOLD THE GUARD
OPEN WHEN OPERATING THIS SAW.
Warning! Always be sure that the tool is switched off and
unplugged before adjusting or checking the tools function.
After use
u After use, wipe off chips and dust adhering to the tool with
a cloth or the like.
u Keep the blade guard clean according to the directions in
the previously covered section.
u Lubricate the sliding portions with machine oil to prevent
rust.
u When storing the tool, pull the carriage toward you fully.
Carrying the tool
u Make sure the tool is unplugged.
u Secure the blade at the 0° bevel angle and turn the base
to the right mitre angle fully with the slide bar locking scre
(28).
u Secure the slide bars after pulling the carriage toward you
fully.
u Lower the handle fully and lock it in the position by
pushing in the saw head locking pin (17).
u Carry the tool by holding the carry handle (22).
u If you remove the clamp, dust bag, etc., you can carry the
tool more easily.
u Carry the tool by one hand holding the carrying handle
(22) and one hand holding the tool base.
Caution! Always secure all moving portions before carrying
the tool.
Saw head locking pin (17) is for carrying and storage
purposes only and not for any cutting operations.
Troubleshooting
Problem Possible Cause Solution
Motor does
not start
Saw not plugged in. Check that all cords are plugged in.
Angle of cut
inaccurate
Mitre table
unlocked.
Use mitre table locking lever (see
Adjusting the mitre angle section.
Too much sawdust
under table.
Vacuum or blow out dust. Wear eye
protection.
Cutting arm
cannot fully
raise, or blade
guard cannot
fully close
Parts Failure. Contact service centre.
Pivot spring not
replaced properly
after service.
Contact service centre.
Sawdust build up. Clean and lubricate moving parts.
Saw head locking
pin not set properly.
Check, adjust, and properly set saw
head locking pin.
Blade binds,
jams or
shakes
Saw blade
damaged.
Replace blade.
Dull blade. Replace or sharpen blade.
Improper blade. Replace blade.
Warped blade. Replace blade.
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker BES700 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker BES700 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 12,24 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info