Handleiding Behringer Xenyx X2442USB (pagina 6 van 19) (Engels)

660523

Verklein

Vergroot

Pagina terug

1/19

Pagina verder

6 XENYX X2442USB/X2222USB/X1832USB/X1622USB User Manual

MIC

Each mono input channel oers a balanced microphone input via the XLR

connector and also features switchable +48 V phantom power supply for

condenser microphones. The XENYX preamps provide undistorted and noise-free

gain as is typically known only from costly outboard preamps.

◊ Please mute your monitor system before you switch on phantom

power. Otherwise potentially damaging thumps will be sent to

your speakers. Please also note the instructions in chapter 5.5

“Voltage supply, phantom power and fuse”.

LINE IN

Each mono input also has a balanced line input on a ¼" jack. You can also connect

unbalanced devices using mono jacks to these inputs.

◊ Please remember that you can use either the microphone input or the

line input of a channel, but not both at the same time!

INSERT

◊ Insert points enable the processing of a signal with dynamic processors

or equalizers. They are sourced pre-fader, pre-EQ and pre-aux send.

Detailed information on using insert points can be found in chapter 5.3.

◊ Unlike the X2442USB, the X1622USB, X1832USB and X2222USB have

their insert points located on the rear of the console.

GAIN

Use the GAIN control to adjust the input gain. This control should always be

turned fully counter-clockwise whenever you connect or disconnect a signal

source to one of the inputs.

The scale has 2 dierent value ranges: the rst value range (+10 to +60 dB)

refers to the MIC input and shows the amplication for the signals fed in there.

The second value range (+10 to -40 dB) refers to the line input and shows its

sensitivity. The settings for equipment with st andard line-level signals (-10dBV

or +4 dBu) look like this: While the GAIN control is turned all the way down,

connect your equipment. Set the GAIN control to the external devices’ standard

output level. If that unit has an output signal level display, it should show 0 dB

during signal peaks. For +4dBu, turn up GAIN slightly, for -10 dBV a bit more.

Fine-tuning of a signal being fed in is done using the level meter. To route the

channel signal to the level meter, you have to press the SOLO switch and set the

MODE switch in the main section to PFL (LEVEL SET).

Using the GAIN control, drive the signal to the 0-dB mark. This way you have

a vast amount of drive headroom for use with very dynamic signals. TheCLIP

display should light up only rarely, preferably never. While ne-tuning,

theequalizer should be set to neutral.

LOW CUT

Additionally, the mono channels of the mixing consoles have a high-slope

LOWCUT lter for eliminating unwanted, low-frequency signal components

(75Hz, 18 dB/octave).

COMPRESSOR

Each mono channel features a built-in compressor which lowers the dynamic

range of the signal and increases its perceived loudness. The loud peaks are

squashed down and the quiet sections are boosted.

Turn the COMP knob clockwise to add more compression eect. The adjacent LED

with light when the eect is engaged.

2.1.2 Equalizer

All mono input channels have a 3-band equalizer with semi-parametric mid

bands. All bands provide boost or cut of up to15 dB. In the central position,

theequalizer is o (at).

The circuitry of the British EQs is based on the technology used in the best-known

top-of-the-line consoles and providing a warm sound without any unwanted

side eects. The result are extremely musical equalizers which, unlike simple

equalizers, cause no side eects such as phase shifting or bandwidth limitation,

even with extreme gain settings of ±15 dB.

All Models

Fig. 2.2: Equalizer of the input channels

The upper (HIGH) and the lower (LOW) bands are shelving lters that increase

or decrease all frequencies above or below their cut-o frequency. The cut-o

frequencies of the upper and lower bands are 12 kHz and 80Hz respectively.

Forthe mid range, the console features a semi-parametric equalizer with a

lter quality (Q) of 1 octave, tunable from 100 Hz to 8 kHz. Use the MID control

to set the amount of boost or cut, and the FREQ control to determine the

centralfrequency.

2.1.3 Monitor and eects busses (Aux Sends)

X1622USB X2442USB

Fig. 2.3: Aux Send control MON and FX in the channel strips

Monitor and eects busses (AUX sends) source their signals via a control from

one or more channels and sum these signals to a so-called bus. This bus signal

is sent to an aux send connector (for monitoring applications: MON OUT) and

then routed, for example, to an active monitor speaker or external eects device.

Inthe latter case, the eects return can then be brought back into the console via

the aux return connectors.

All monitor and eects busses are mono, are tapped into post EQ and oer

amplication of up to +15 dB.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Behringer Xenyx X2442USB Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Behringer Xenyx X2442USB

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info