Handleiding Aeris A100 (pagina 24 van 32) (Engels)

618063

Verklein

Vergroot

Pagina terug

1/32

Pagina verder

A100 OPERATING MANUAL

Battery Removal

• Remove the Retaining Bar located across the lower portion of the Battery (Fig. 65a).

• Remove the Cover O-ring. DO NOT use tools.

• Slide the Battery up and out of the Battery Compartment.

Inspection

• Closely check all of the sealing surfaces for any signs of damage that might impair proper sealing.

• Inspect the Button, Lens, and Housing to ensure they are not cracked or damaged.





Battery Installation

• Slide a new 3 volt type CR2450 Lithium Battery, ( - ) negative side down into the Battery Compartment. Slide it in from the

right side and ensure that it slides under the contact clip on the left rim (Fig. 66).

• Orient the Retaining Bar across the lower portion of the Battery and carefully push it down into position (Fig. 67).

Battery Cover and Retaining Ring Installation

• Lightly lubricate a new Cover O-ring* with silicone grease and place it on the inner rim of the Battery Cover (Fig. 68).

Ensure that it is evenly seated.

*The O-ring must be a genuine AERIS part that can be purchased from an Authorized AERIS Dealer.

Use of any other O-ring will void the warranty.

• Slide the Cover Ring, top portion ﬁrst (small opening), onto your thumb.

• Carefully place the Battery Cover (with O-ring) into position on the rim of the Battery Compartment, then press it evenly and

completely down into place with your same thumb.

• Maintain the Battery Cover securely in place and, using your other hand, slide the Cover Ring down off your thumb and into

position around the Battery Compartment.

• The tabs on the Cover Ring ﬁt down into the two slots located at the 2 and 8 o'clock positions.

• Using your ﬁngers, turn the Ring counter clockwise 5 degrees until the tabs engage (Fig. 69), then tighten it 5 more degrees

by turning it counter clockwise with the aide of a small blade screwdriver (Fig. 70).

• While tightening the Retaining Ring, exert continuous inward pressure on it until it is secured in the proper position. A small

symbol located on the Ring should be aligned with the Locked symbol located on the Housing (Fig. 71a).

Inspection

• Activate the unit and watch carefully as it performs a full diagnostic and battery check, and enters Surface Mode.

• Observe the LCD display to ensure it is consistently clear and sharp in contrast throughout the screen.





RETURNING THE MODULE TO BOOT

• If the boot was ﬁtted with a spacer and it was previously removed, replace the spacer into the boot.

• Orient the module over the opening in the boot, and dip the bottom edge into it while pressing the top edge with the palm of

your hand. Stop pressing when the bottom edge of the module has just entered the boot.

• Correct the alignment of the module as needed so that it is straight.

• Press the module completely into place with your thumbs, watching the alignment, until it snaps into place.

ALTITUDE SENSING AND ADJUSTMENT

Altitude (i.e., ambient pressure) is measured upon activation and every 15 minutes until a dive is made.

> Measurements are only taken when the unit is dry.

> Two readings are taken, the second reading 5 seconds after the ﬁrst. The readings must be within 1 foot (30 cm) of each

other to record that ambient pressure as the current Altitude.

> No adjustments are made during any time that the Wet Contacts are bridged.

> When diving in high altitude waters from 3,001 to 14,000 feet (916 to 4,270 meters), the A100 automatically adjusts to

these conditions providing corrected Depth, and reduced No Deco and O2 Times at intervals of 1,000 feet (305 meters).

> At Sea Level, calculations are based upon an Altitude of 6,000 feet.

> All adjustments for Altitudes greater than 11,000 feet (3,355 meters) are then made to allowable dive times for 14,000 feet

(4,270 meters).

> The A100 will not function as a Dive Computer above 14,000 feet (4,270 meters).

Fig. 69 - TABS ENGAGE

Fig. 70 - TABS TIGHT

Fig. 71 - RING SECURE

Fig. 66 - BATTERY

Fig. 67 - RETAINING BAR

Fig. 68 - COVER O-RING

Fig. 65 - RETAINING BAR

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Aeris A100 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info