755222
105
Verklein
Vergroot
Pagina terug
1/116
Pagina verder
Appendix IV – Wiring Information
99
LED9 (state of relay 2): Lights when relay 1 is
activated.
LED10 (state of transistor output 3): Lights
when transistor output 3 is activated.
LED11 (state of transistor output 4): Lights
when transistor output 4 is activated.
LED12 (state of strobe output): Lights when
the strobe output is activated.
LED12 (state of bell output): Lights when the
bell output is activated.
LED14: (state of transistor output 5): Lights
when transistor output 5 is activated.
1.28 Fuses
The alarm centre board contains the following
fuses that reset automatically.
Note that voltage must be removed
completely to make a reset!
F1: Battery charge circuit
F2: Output 12V DC bus 1
F3: Output 12V DC bus 2
F4: External alarm sounder
F5: 12V DC output for supplying external devices
F6: Bell output
1.29 Resistors
The alarm centre has 8 connection blocks for
zones. Two or more sensors can be connected to
each zone. Either DEOL or NC can be used for
wiring the zones.
Method 1: Zone closed NC (no resistor inserted)
This is the factory default method. If you use
sensors with normally open contacts, select
“Invert” under the zone attributes. In this variant,
the system can only detect whether the zone is
opened and it always registers an opening as an
alarm in this zone. The tamper contacts must be
connected to the alarm contacts of the respective
tamper zones. For wiring with this method, you
need 4 lines. Note that the voltage supply of the
sensor requires two additional lines.
Method 2: Zone closed by resistors (2 resistors
used)
In Variant B, the tamper contact and alarm
contact are monitored in one zone. In the event
of a change of resistance, the alarm station can
distinguish whether it is a real alarm or tampering.
The first figure shows the connection of just one
sensor to a zone. In the lower figure, two sensors
are serially connected to a zone. Note that you
can choose different variations of resistance
values.
Alarm resistance (±5%) Series resistance (±5%)
4.7kOhm 2.7kOhm
1kOhm 1kOhm
4.7kOhm 4.7kOhm
2.7kOhm 2.7kOhm
105

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Abus Terxon LX - AZ4200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Abus Terxon LX - AZ4200 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Abus Terxon LX - AZ4200

Abus Terxon LX - AZ4200 Installatiehandleiding - Deutsch - 31 pagina's

Abus Terxon LX - AZ4200 Gebruiksaanwijzing - Deutsch - 16 pagina's

Abus Terxon LX - AZ4200 Gebruiksaanwijzing - English - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info